Following a week of getting dragged on YouTube and Reddit for a performance throttling issue, Apple’s new is now rid of the problem through a software patch. Apple issued a statement regarding the issue and its new fix,. “Following extensive performance testing under numerous workloads, we've identified that there is a missing digital key in the firmware that impacts the thermal management system and could drive clock speeds down under heavy thermal loads on the new MacBook Pro. A bug fix is included in today's macOS High Sierra 10.13.6 Supplemental Update and is recommended.

We apologize to any customer who has experienced less than optimal performance on their new systems. Customers can expect the new 15-inch MacBook Pro to be up to 70% faster, and the 13-inch MacBook Pro with Touch Bar to be up to 2X faster, as shown in the performance results on our website.”.

The fix comes after technology YouTube personality David Lee uncovered an issue in the 15-inch with an Intel Core i9 processor that when the laptop reaches a certain temperature while under load. Lee found the issue when rendering 4K video through Adobe Premiere Pro. According to Apple, this issue actually affected all versions of the new 13-inch and 15-inch MacBook Pro models regardless of the processor inside, and was the result of a bug within the computers’ thermal management systems. Apple has since added performance results for the very same task Lee attempted on video. While we had not encountered these issues in our review of either 2018 MacBook Pro, this discovery and resulting solution couldn’t have come at a better time for Apple. Given that the company has recently refocused on its Mac hardware over the past few years following increasing complaints by disgruntled fans, another blemish on its reputation could be harmful.

Apple wasn’t clear on exactly when the macOS 10.13.6 update would be available, at the time of writing, so be sure to keep checking that Mac App Store.

It is possible to update the firmware on an Onagofly micro drone on Mac OS X using the QGroundControl software. The download for the software can be found here:. You will also need the firmware provided by Onagofly, which is currently version 630. The firmware (with modified file extension) can be found here: Step 1: Change firmware extension to px4 This step is not necessary if you downloaded the firmware using the link in this post, but by default the firmware file is named ONAGOfly0630.ong. This means you will need to rename it to ONAGOfly0630.px4 as the QGroundControl app will only allow you to select.hex,.bin, and.px4 files, and since we are uploading firmware to the Pixhawk PX4 FMU Step 2: Prepare Drone Leave the drone powered off, or disconnect the battery entirely if you are able, and connect a micro USB cable. Step 3: Open QGroundControl Without connecting it to your computer, start up QGroundControl. Step 4: Select “Firmware” This is mode allows QGroundControl to update the firmware on the Onagofly. Plug in (or unplug and re-plug in) the USB cable to detect the Pixhawk flight controller.

Step 5: Configure firmware update Once your device is detected, you will need to change the firmware settings to properly update using the Onagofly firmware, rather than the default PX4 or ArduPilot stack. Select “ArduPilot Flight Stack”. Quad – APM:Copter V3.3.3. Check the “Advanced settings” box.

Choose “Custom firmware file”. Click OK. Step 6: Select firmware file Navigate to the location of the ONAGOfly0630.px4 firmware file and select it. Step 7: Update Complete You should see some status updates followed by a message saying “Upgrade complete”. A few seconds later you should hear the startup noise, and the device will be detected by QGroundControl. It took several attempts to get the firmware to properly upload, so if it is unsuccessful, try again. When I was finally able to load the firmware, I first loaded the Beta ArduCopter stack, then the Onagofly.

Canon pixma mg3100 printer drivers for mac. I use my fingernails to lift the black GPS cover. A guitar pic or the tools used for opening iPods etc will work just fine. I put a stick on paper dot on the cover and the O body so that it will go back the right way round or the antenna won’t reconnect. You will see the antenna appears to be just a 6.5mm square tab.I have looked at GPS antenna on all kinds of mobiles and they come in a wide variety of shapes and sizes. The one I am going to try looks like just a 60m length of wire. Unfortunately, I live in a basement apartment with zero GPS so I have to go outside to get reception. I will let you know how I get on.

I think a degree in either Magic or antenna design would be good. As I have neither I will try the guestimation method. So I get a lot further with my net book and windows BUT fail at the last hurdle. The flash halts with the following message.

Solved Is There A Firmware Update For Macbook Pro

QGroundControl can upgrade the firmware on Pixhawk devices, SiK Radios and PX4 Flow Smart Cameras. All QGroundControl connections to vehicles must be disconnected prior to firmware upgrade.

Solved Is There A Firmware Update For Mac

Please unplug your Pixhawk and/or Radio from USB. Plug in your device via USB to start firmware upgrade.

Found device: Pixhawk Connected to bootloader: Version: 4 Board ID: 9 Flash size: 2080768 Downloading firmware. From: C:/Users/Reester78/Downloads/ONAGOfly0630.px4 Download complete MAVAUTOPILOT = 12 Firmware file missing parameterxmlsize key Firmware file missing airframexmlsize key Succesfully decompressed image Erasing previous program. Erase complete Programming new version.

Error: Flash failed: Write failed: OS error: The semaphore timeout period has expired. At address 0x00088240 Upgrade cancelled - If upgrade failed, make sure to connect directly to a powered USB port on your computer, not through a USB hub.

Also make sure you are only powered via USB not battery.